View MIC6315-40D2U_5016703.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

MIC6315
Micrel
MIC6315
Open-Drain P Reset Circuit
General Description
The MIC6315 is an inexpensive reset generator circuit that monitors power supplies in microprocessor based systems. The function of this device is to assert a reset if either the power supply drops below a designated reset threshold level or /MR is forced low. Several different reset threshold levels are available to accommodate 3V, 3.3V or 5V powered systems. The MIC6315 has an active low, open-drain /RESET output. The reset output is guaranteed to remain asserted for a minimum of either 20ms, 140ms, or 1100ms after VCC has risen above the designed reset threshold level. The MIC6315 comes in a 4-pin SOT-143 package.
Features
* Precisionvoltagemonitorfor3V,3.3Vor5Vpowersupplies * /RESETremainsvalidwithVCC as low as 1V * 5Asupplycurrent * 20ms,140ms,or1100msminimumresetpulsewidths available * Manualresetinput * 4-pinSOT-143package
Applications
* * * * * Portableequipment Intelligentinstruments Criticalmicroprocessorpowermonitoring Printers/computers Embeddedcontrollers
Typical Application
VCC
VCC VCC
10k
MIC6315
MR RESET
P RESET
Micrel, Inc. * 2180 Fortune Drive * San Jose, CA 95131 * USA * tel + 1 (408) 944-0800 * fax + 1 (408) 474-1000 * http://www.micrel.com
September 2008
1
M9999-091608
MIC6315
Micrel
Pb-Free Part Number Nominal VTH (V) 2.63 2.93 3.00 3.08 4.00 4.10 4.38 4.63 2.63 2.93 3.00 3.08 4.00 4.10 4.20 4.38 4.63 2.63 2.93 3.00 3.08 4.00 4.10 4.38 4.63 Min. tRST (ms) 20 20 20 20 20 20 20 20 140 140 140 140 140 140 140 140 140 1100 1100 1100 1100 1100 1100 1100 1100 Operating Temp. Range -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C
Ordering Information(1, 2)
Standard Part Number Marking NY NM N2 NF NW N6 NG NQ NR NP N3 NU N8 N5 0N NH NX NS NN N4 2N M9 M7 NJ NZ MIC6315-26D2U MIC6315-29D2U MIC6315-30D2U MIC6315-31D2U MIC6315-40D2U MIC6315-41D2U MIC6315-44D2U MIC6315-46D2U MIC6315-26D3U MIC6315-29D3U MIC6315-30D3U MIC6315-31D3U MIC6315-40D3U MIC6315-41D3U MIC6315-42D3U MIC6315-44D3U MIC6315-46D3U MIC6315-26D4U MIC6315-29D4U MIC6315-30D4U MIC6315-31D4U MIC6315-40D4U MIC6315-41D4U MIC6315-44D4U MIC6315-46D4U
Notes:
Marking NY NM N2 NF NW N6 NG NQ NR NP N3 NU N8 N5 0N NH NX NS NN N4 2N M9 M7 NJ NZ
Package 4-lead SOT-143 4-lead SOT-143 4-lead SOT-143 4-lead SOT-143 4-lead SOT-143 4-lead SOT-143 4-lead SOT-143 4-lead SOT-143 4-lead SOT-143 4-lead SOT-143 4-lead SOT-143 4-lead SOT-143 4-lead SOT-143 4-lead SOT-143 4-lead SOT-143 4-lead SOT-143 4-lead SOT-143 4-lead SOT-143 4-lead SOT-143 4-lead SOT-143 4-lead SOT-143 4-lead SOT-143 4-lead SOT-143 4-lead SOT-143 4-lead SOT-143
MIC6315-26D2UY MIC6315-29D2UY MIC6315-30D2UY MIC6315-31D2UY MIC6315-40D2UY MIC6315-41D2UY MIC6315-44D2UY MIC6315-46D2UY MIC6315-26D3UY MIC6315-29D3UY MIC6315-30D3UY MIC6315-31D3UY MIC6315-40D3UY MIC6315-41D3UY MIC6315-42D3UY MIC6315-44D3UY MIC6315-46D3UY MIC6315-26D4UY MIC6315-29D4UY MIC6315-30D4UY MIC6315-31D4UY MIC6315-40D4UY MIC6315-41D4UY MIC6315-44D4UY MIC6315-46D4UY
1. Alldevicesavailableintapeandreelonly. 2. Partsnotyetassignedanidentificationcodeareshownas"zz".ContactMicrelfordetails.Minimumordermayapply.
Pin Configuration
GND 1 4 VCC
MIC6315
RESET 2 3 MR
MIC6315-xxDyU 4-Lead SOT-143
Pin Description
Pin Number 1 2 3 Pin Name GND /RESET /MR Pin Function ICGroundPin. /RESET goes low if VCC falls below the reset threshold and remains asserted for one reset timeout period after VCC exceeds the reset threshold.
ManualResetInput.Alogiclowon/MRforcesareset.Theresetwillremain asserted as long as /MR is held low and for one reset timeout period after /MR goes high. This input can be shorted to ground via a switch or be driven by TTL or CMOS logic. Float if unused. PowerSupplyInput.
4
VCC
M9999-091608
2
September 2008
MIC6315
Micrel
Absolute Maximum Ratings(1)
Terminal Voltage (VCC, /RESET) ........................................-0.3V to 6.0V (/MR) ..........................................-0.3V to (VCC + 0.3V) Rate of Rise (VCC) .................................................. 100V/s Input Current (VCC, /MR) ............................................ 20mA Output Current (/RESET) ........................................... 20mA Lead Temperature (soldering, 10 sec.) ...................... 300C Storage Temperature (TS) ......................... -65C to 150C ESD Rating(3) ............................................................... 3kV
Operating Ratings(2)
Operating Temperature Range ................... -40C to +85C Input Voltage (/RESET) .................................... GND - 5.5V PowerDissipation(TA = +70C) .............................. 320mW
Electrical Characteristics
For typical values, VCC = 2.5V to 5.5V, TA = 25C; bold valuesindicate-40CTA+85C;unlessnoted Symbol VCC ICC Parameter Condition Min 1 VCC = 5.5V, no load Note 4 D2U D3U D4U VOL /RESET Output Voltage VCC > 2.5V, ISINK=1.2mA /RESET Output Leakage VIH VIL
Notes: 1. Exceeding the absolute maximum rating may damage the device. 2. The device is not guaranteed to function outside its operating rating. 3. Devices are ESD sensitive. Handling precautions recommended. Human body model, 1.5k in series with 100pF. 4. Various reset thresholds available. See ordering information or contact factory.
Typ 5 5
Max 5.5 15 10 VTH+2.5% 44 320 2500 0.4 0.3 0.3 1
Units V A A V ms ms ms V V V A s s V V
Operating Voltage Range Supply Current Reset Voltage Threshold ResetTimeoutPeriod VCC = 3.6V, no load
tRST
VTH
VTH-2.5% 20 140 1100 10 2.3 0.7xVCC
VTH 28 200 1500 0.5
VCC4.0V,ISINK=3.2mA
/RESET deasserted VTH > 4.0V VTH < 4.0V VTH < 4.0V VTH > 4.0V
VCC1.0V,ISINK=50A
/MRMinimumPulseWidth /MRtoResetDelay /MR Input Threshold /MR Input Threshold /MRPull-UpResistance /MR Glitch Immunity
0.8 20 100 0.25xVCC 30
V V k ns
10
September 2008
3
M9999-091608
MIC6315
Micrel
Timing Diagram
VCC /MR VTH
/RESET
tRST
tRST
Reset Timing Diagram
Functional Diagram
VCC (4) Reset Threshold (V) MR (3)
+ RESET GENERATOR
RESET (2)
GND (1)
M9999-091608
4
September 2008
MIC6315
Micrel Wire OR'ing The /RESET Output Because the RESET output is open-drain, several reset sources can be wire-ORed, in parallel, to allow resets from multiple sources. VCC Transients The MIC6315 is relatively immune to negative-going VCC glitches below the reset threshold. Typically, a negative-going transient 125mV below the reset threshold with a duration of 20sorlesswillnotcauseanunwantedreset.Ifadditional transient immunity is needed, a bypass capacitor can be placed a close as possible to the MIC6315.
+3.3V VCC +5.0V VCC
10k
Applications Information
Microprocessor Reset The /RESET pin is asserted whenever VCC falls below the reset threshold voltage or if /MR (manual reset) is forced low. The /RESET pin remains asserted for the duration of the reset timeout period after VCC has risen above the reset threshold or /MR has returned high. The reset function ensure the microprocessor is properly reset and powers up in a known condition after a power failure. /RESET will remain valid with VCC as low as 1V. The /RESET output is a simple open-drain N-channel MOSFET structure.A pull-up resistor must be used to pull this output up to some voltage. For most applications, this voltage will be the same power supply that supplies VCC to the MIC6315. It is possible, however, to tie this resistor to some other voltage. This will allow the MIC6315 to monitor one voltage while level-shifting the /RESET output to some other voltage. The pull-up voltage must be limited to 6.0V or less (absolute maximum) to avoid damage to the MIC6315. The resistor must be small enough to supply current to the inputs and leakage paths that are driven by the /RESET output. /RESET Valid at Low Voltage AsVCC drops to 0V, the MIC6315 will no longer be able to pullthe/RESEToutputlow.Atthispoint,thepull-upresistor will pull the output high. The value of the pull-up resistor and the voltage it is connected to will affect the point at which this happens.
MIC6315
MR RESET
5V SYSTEM RESET
MIC6315 Used in a Multiple Supply System
September 2008
5
M9999-091608
MIC6315
Micrel
Package Information
0.950 (0.0374) TYP 1.40 (0.055) 2.50 (0.098) 1.20 (0.047) 2.10 (0.083) C L 1.12 (0.044) 0.81 (0.032)
C L
DIMENSIONS: MM (INCH) 8 0 0.150 (0.0059) 0.089 (0.0035)
3.05 (0.120) 2.67 (0.105)
0.800 (0.031) TYP 0.400 (0.016) TYP 3 PLACES
0.10 (0.004) 0.013 (0.0005)
0.41 (0.016) 0.13 (0.005)
4-Pin SOT-143 (U)
tel + 1 (408) 944-0800 fax + 1 (408) 474-1000 web http://www.micrel.com The information furnished by Micrel in this datasheet is believed to be accurate and reliable. However, no responsibility is assumed by Micrel for its use. Micrelreservestherighttochangecircuitryandspecificationsatanytimewithoutnotificationtothecustomer.
MicrelProductsarenotdesignedorauthorizedforuseascomponentsinlifesupportappliances,devicesorsystemswheremalfunctionofaproductcan reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a) are intended for surgical implant into thebodyor(b)supportorsustainlife,andwhosefailuretoperformcanbereasonablyexpectedtoresultinasignificantinjurytotheuser.APurchaser's useorsaleofMicrelProductsforuseinlifesupportappliances,devicesorsystemsisatPurchaser'sownriskandPurchaseragreestofullyindemnify Micrel for any damages resulting from such use or sale. (c) 2005 Micrel, Incorporated. M9999-091608
MICREL, INC.
2180 FORTUNE DRIVE SAN JOSE, CA 95131
USA
6
September 2008

▲Up To Search▲

Price & Availability of MIC6315-40D2U

	To Download MIC6315-40D2U Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .